A vape coil is a heating element formed from a stretch of resistance wire in the shape of a circular pattern. The wick is wet with e-juice and wrapped around the coil. When you power up your device and heat the coil, the e-juice vaporizes, and you consume this vapor.
Many vaping professionals create their coil heads instead of purchasing temporary coil heads every week. But why do people make their coil? They can control the kind of vapor you inhale by making your coils.
Vaping enthusiasts not only find delight in their pastime, but they also get to enjoy the benefits of their effort. It takes a lot of focus to become excellent at it. It’s understandable for first-time builders to want to do it right the first time. If it is your first time making a vape coil, you’re at the right place. Read on to know the tools and equipment needed, along with steps to make vape coils like a pro.
How to make a vape coil?
Before beginning the coiling of the wire, you need to make sure that all the equipment is available to you for use. If you don’t want to get into the hassle of creating your coils, there is a top quality vape box mod available online for you to purchase.
But if you’re curious about making your coils, here are some essential tools you must have:
- Kanthal vape coil wire
- The atomizer as per your preference
- Needle pliers
- Small screwdriver
- Ohm’s reader
- A regulated mod
- A coil jig
- Wire cutters
Method 1:
When you have all the tools given above, you’re ready to make your first coil. The steps are as follows:
Step 1:
First, you’ll need to use the wire clippers to take a piece of Kanthal resistance wire. Aim for a length of around 3 inches, but if this is your first time, cut a little more.
Step 2:
Form a ‘+’ with both the coil jig and the wire by holding it in your left hand. Then, slide one side of the wire under your thumb.
To keep the Kanthal from moving, press down hard with your thumb and align it with the 2.5mm area on the coil jig. Wrap your thread around it gently now, being sure to maintain the Kanthal as firm as possible throughout the wrapping to avoid any slack.
Step 3:
Place your new coil on the jig and leave it aside for now. You’ll need to adjust the post fasteners on your assembly deck until the tail ends of your coil easily fit through.
Place one end through positive and the other through negative. If you don’t want your coil to change its form, keep it on the coil jig when you are doing this.
Step 4:
Take the screwdriver and fasten the screws to hold the wires in place after you’ve got both ends through their holes.
Push and pull the coil with your jig until it’s precisely where you want it. Remove the coil jig when you’re happy with the location and the coil is as uniform as possible.
Step 5:
Turn on your ohms detector and insert or screw your build deck. Your coil should read 1.2 ohms if you’ve done everything correctly.
If your ohms are shifting, double-check that your post fasteners are snug and that the coil is not contacting the construction deck since this will alter the results.
Method 2: After cutting the wire, oxidize it
In this method, all the processes are similar to the first method. However, you can also choose to oxidize the wire after cutting it. You should use tweezers to hold the wire’s end. Light a flame and gently heat one end of the kanthal wire till it glows orange, then slide the light down the length of the wire slowly. Allow your wire to cool before grabbing the other end and repeating the process. The wire will become less “springy” and simpler to deal with after being oxidized.
Method 3: Coiling for RDA (Rebuildable Dripping Atomizer)
Preparing coils for RDAs is typically a simple procedure. Examine the deck to see if it is a dual or single-coil atomizer. Then look at the deck size to determine how big you can make your build—you don’t want your coils to hit the top cap since that would create a sort. Most RDAs can accommodate coils with at least 3 mm diameter, and many can accommodate coils with considerably bigger IDs.
Check the location of the posts after you’ve determined the size and the number of your coils. Some decks need the leaders to face the same position, while others require them to meet the other way. It’s worth noting that certain postless decks may need cutting the leads ahead of time. Place the wires in the threaded inserts and fix them in place with the screws after your coils are wrapped and ready.
Method 4: Making parallel coil
The parallel coil is a multi-strand string that does not need tools or drills. The coil is created by wrapping two or more wires adjacent to one other. When designing parallel coils, keep in mind that the number of wire strands splits resistance. Therefore, be conscious of your device’s limitations. A twin concurrent 26-gauge Kanthal coil is an excellent place to start for novices.
Method 5: Building using dual coil
You may have observed that the boards of several atomizers are intended to hold two coils or dual-coil designs. Not all atomizers support both, and even if they do, one of the two alternatives will typically provide more incredible performance. Check the atomizer’s posts since each vape coil must pass through both. Check the atomizer’s airflow as well. You’re probably viewing at a dual-coil atomizer if the air hits the posts from both sides.
To guarantee that both coils heat up correctly while completing a twin coil setup, they must be of equal size and shape. Dual-coil designs produce more air than a single coil with the exact specifications, but they need dual power.
The strength should be precisely one-half of each coil’s resistance when using two identical coils. In other words, if you used two 0.6-ohm coils in a dual-coil design, your construct should be 0.3 ohms. Your resistance will return to 0.6 ohms if you remove one of those coils.
In conclusion
It’s vital to remember that knowing the limitations of your gadget, electronics, and batteries is critical when designing or rebuilding your coils. Never build up to the point when your resistance exceeds your safe working limit. However, it’s not difficult to make a primary coil. The coils may be constructed if the fundamentals are known. The methods and tips given above will help you create different types of coils for your vape.
